Nexus Automech Private Limited
Ahmedabad, Gujarat
GST No. 24AAICN2973L1Z2
TrustSEAL Verified
Call 07942821796 75% Response Rate
SEND EMAIL
Service Details:
| Pressure Range | 0-500 bar |
| Process Connection Type | Flange Connection |
| Output Signal | Foundation Fieldbus / Modbus |
| Measurement Type | Absolute Pressure |
| Supply Voltage | 220 V AC |
| Temperature Range | -40DegC to +125DegC |
| Process Wetted Material | Hastelloy |
| Accuracy | +-0.5% FS |
The electronic dp Deltabar FMD72 is a differential pressure system, used to measure the pressure, level, volume or mass of liquids in pressurized tanks or distillation columns/evaporators. The high pressure sensor (HP) measures the hydrostatic pressure. The low pressure sensor (LP) measures the head pressure. The level is calculated in the transmitter using these two digital values. The electronic dp system eliminates issues of traditional differential pressure measurements.
For differential pressure, level, volume or mass measurement of liquids in pressurized tanks and distillation columns/evaporators.
Process connections: Threads, flanges and hygienic connections
Process temperature: -40 to +125°C (-40 to +257°F), optional 250°C (480°F)
Measuring range: 400mbar to +40bar (6 to 600psi)
Accuracy: Single sensor up to ±0.05%, system up to ±0.07%
International explosion protection certificates, hygienic approvals
Eliminates traditional mechanical issues resulting in greater process availability and reliability
Safety risks are minimized with the new electronic differential pressure system architecture and design
Lowest total cost of ownership due to reduced installation time, maintenance, downtime and spare requirements
Multivariable level measurement: HART-based differential pressure, head pressure and sensor temperatures from one system
Continuous health indication of the entire system via HART-based diagnostic
High reproducibility and long-term stability
Process safety assured with small flush mounted process connections in hygienic applications
Service Details:
| Pressure Range | 0-500 bar |
| Process Connection Type | Tri-clamp |
| Output Signal | HART Communication |
| Measurement Type | Absolute Pressure |
| Temperature Range | -40DegC to +125DegC |
| Process Wetted Material | Monel |
| Accuracy | +-0.5% FS |
The Deltabar PMD55 differential pressure transmitter with piezoresistive sensor and welded metallic membrane is typically used in process or environmental applications for continuous measurement of pressure differences in liquids, vapors and gases. Quick Setup with adjustable measuring range allows simple commissioning, reduces costs and saves time. SIL2 according to IEC 61508 / IEC 61511.
For level, volume or mass measurement in liquids, differential pressure monitoring, e.g. of filters and pumps as well as flow measurement (volume or mass flow) in conjunction with primary elements in gases, vapors and liquids.
Process connections: Threads
Process temperature: -40 to 85°C (-40 to 185°F)
Measuring ranges: 0.5mbar to 40bar (0.0072 to 600psi)
Accuracy: ±0.1%, "Platinum" ±0.075% (optional)
International explosion protection certificates, SIL
Easy menu-guided commissioning via local display, 4 to 20mA with HART, PROFIBUS PA, FOUNDATION Fieldbus
Easy process adaptation to impulse line high-pressure/low-pressure change via electric switch on the main electronics
Compact design and modular concept for easy replacement of display or electronics
Process pressure up to SIL2, certified to IEC 61508 and IEC 61511
Global usage thanks to the widest range of approvals for industries and applications
Service Details:
| Pressure Range | 0-500 bar |
| Process Connection Type | Tri-clamp |
| Output Signal | HART Communication |
| Supply Voltage | 36 V |
| Process Wetted Material | Monel |
| Accuracy | +-0.5% FS |
This transmitter belongs to the new Deltabar generation. It is robust and easy to operate either locally or remotely. The transmitter can be controlled wireless via app on a mobile device using a secure Bluetooth connection. The PMD55B allows condition-based maintenance which increases efficiency in technical service significantly.
The software is designed to simplify the handling. Intuitive wizards guide you through the setup and proof testing of the device which minimizes operating errors.
Pressure measuring range: up to 40 bar (600 psi)
Static pressure up to 250bar (3750psi)
Accuracy: up to +/-0.055%
Wireless control of the device in the process area with the SmartBlue App without interrupting the process
Reduce on site accidents and protect equipment when instruments are in difficult to reach areas
Reduce systematic failures - error free SIL commissioning and instrument guided proof testing
Service Details:
| Minimum Order Quantity | 1 Piece |
| DP Range | 0–100 mbar |
| Application | Filter DP |
| Output Signal | 4–20 mA HART |
| Process Connection | Flanged |
| Turn Down Ratio | 10:1 |
| Accuracy | ±0.075% |
| Mounting Type | 2 in Pipe |
| Hazardous Approval | Safe Area |
Additional Information:
Service Details:
| Minimum Order Quantity | 1 Piece |
| DP Range | 0–10 bar |
| Application | Flow |
| Output Signal | PROFIBUS PA, 4–20 mA HART, FOUNDATION FFB |
| Process Connection | Threads |
| Turn Down Ratio | 10:1 |
| Accuracy | ±0.075% |
| Hazardous Approval | Safe Area |
Process connections: Threads
Process temperature: -40 to 85°C (-40 to 185°F)
Measuring ranges: 0.5mbar to 40bar (0.0072 to 600psi)
Accuracy: ±0.1%, "Platinum" ±0.075% (optional)
International explosion protection certificates, SIL
Additional Information:
Service Details:
| Pressure Range | 0-500 bar |
The electronic dp Deltabar FMD71 is a differential pressure system, used to measure the pressure or level, volume or mass of liquids in pressurized tanks or distillation columns/evaporators. The high pressure sensor (HP) measures the hydrostatic pressure. The low pressure sensor (LP) measures the head pressure. The level is calculated in the transmitter using these two digital values. The electronic dp system eliminates issues of traditional differential pressure measurements.
For differential pressure, level, volume or mass measurement of liquids in pressurized tanks and distillation columns/evaporators.
Process connections: Threads, flanges and hygienic connections
Process temperature: -40 up to +150°C (-40 to +302°F)
Measuring range: 100mbar to +40bar (6 to 600psi)
Accuracy: Single sensor up to ±0.05%, system up to ±0.07%
International explosion protection certificates, hygienic approvals
Eliminates traditional mechanical issues resulting in greater process availability and reliability
Overload-resistant high purity ceramic sensor (99.9% Al2O3)
Safety risks are minimized with the new electronic differential pressure system architecture and design
Lowest total cost of ownership due to reduced installation time, maintenance, downtime and spare requirements
Multivariable level measurement: HART-based differential pressure, head pressure and sensor temperatures from one system
Continuous health indication of the entire system via HART-based diagnostic
High reproducibility and long-term stability
Service Details:
| Minimum Order Quantity | 1 Piece |
| DP Range | 0–100 mbar |
| Application | Filter DP |
| Output Signal | PROFIBUS PA, 4–20 mA HART |
| Process Connection | ¼ in NPT |
| Turn Down Ratio | 100:1 |
| Diaphragm Material | Monel |
| Accuracy | ±0.2% |
| Mounting Type | Wall Mount |
| Hazardous Approval | Safe Area |
Standard:
up to 0.05 %
Platinum:
up to 0.035 %
10 mbar...250 bar
(0.15 psi...3750 psi)
-40°C...+110°C
(-40°F...+230°F)
10 mbar...250 bar
(0.15 psi...3750 psi)
Pressure measuring ranges up to 250 bar (3750 psi) (gauge/absolute) and 40 bar (600psi) (dp)
Static pressure up to 420bar (6300psi)
Accuracy: up to +/- 0.035%
Additional Information:
Service Details:
| Minimum Order Quantity | 1 Piece |
| Pressure Range | 0–100 kPa |
| Output Signal | 4–20 mA |
| Process Connection | Flanged |
| Medium | Non-Corrosive Gas |
| Accuracy | ±0.75% FS |
| Supply Voltage | 10–30 V DC |
| Application | Flow Measurement |
0,075% + influence of diaphragm seal
-40°C...400°C
(-40°F...752°F)
100mbar...40bar
(1.5psi ... 600 psi)
160bar (2400 psi)
Alloy C276
316L
Monel
Tantalum
Additional Information: